PIE 830 - High Accuracy Multifunction Diagnostic Calibrator with Dual Display

• Lighten up your toolbox
  Compact calibrator replaces toolbox of single function devices Milliamp • Voltage • Frequency • pH Thermocouples • RTDs • Pressure • Troubleshooter
• First multifunction calibrator with three troubleshooting tools
  Troubleshoot loop problems - Quickly diagnose ground fault and current leakage with patented Loop Diagnostic technology.
  Automatically detect 2, 3 or 4 wire RTDs - Trouble shoot sensor connections and find broken wires with patented technology.
  Troubleshoot wiring problems - Beep with continuity checker.
• Lighten up your toolbox
  Compact calibrator replaces toolbox of single function devices Milliamp • Voltage • Frequency • pH Thermocouples • RTDs • Pressure • Troubleshooter
• Simulate pH probes & calibrate pH transmitters
  Source from 0.000 to 14.000 pH @ 25 degrees C (77 degrees F) into transmitters & analyzers corresponding to -414.12 to +414.12 mV
• Technician friendly operation
  Intuitive EZ-DIAL Double Click Menu makes it easier to setup than other multifunction calibrators. Same as the single function PIE Calibrators.
• Calibrate 2 wire transmitters - control input & monitor output
  Simulate transmitter inputs while powering it with the internal isolated 24 V supply & measuring the 4-20 mA output. Dual display of transmitter input & output. Simplify HART hookups with built-in 250 Ohm resistor
• Use it as a milliamp and voltage calibrator
  Source 0 to 24.000 mA, 0 to 10.250 V dc, -20.000 to 99.999 mV and -500.00 to 999.99 mV. Read to 24.000 mA, 60.00 V dc -99.999 to +99.999 mV and -999.99 to +999.99 mV. Simulate 2-Wire Transmitters.
• Calibrate directly in temperature to 0.1 degrees C & 0.1 degrees F
  Compatible with the instruments you use including all brands of smart transmitters and PLCs with 14 thermocouple & 9 RTD types.
• Checkout flow & vibration systems
  To 2000 CPM (Counts-Per-Minute), 999.99 Hz, 9999.9 Hz & 20.000 kHz.
• Measure pressure with optional pressure modules
  32 modules for gauge, differential, absolute & compound pressure
• Easy to read
  Turn on the backlight & easily see the display in dark areas of the plant
• Quickly set any three outputs plus automatic stepping & ramping
  Easily set any value quickly with the adjustable "DIAL" plus store any three output settings for instant recall with the EZ-CHECK™ switch. Choose between 2, 3, 5 & 11 steps to automatically increment the output in 100%, 50%, 25% or 10% of span. Select RAMP to smoothly increase and decrease the output between Zero and Span. Set step/ramp time to match your system from 5, 6, 7, 8, 10, 15, 20, 25, 30 and 60 seconds.
• Measure temperature sensors, frequency pickups, loop currents, voltage levels & pressures
  Check the values of your process sensors. Instantly recall MAX and MIN values to see process variability

Advantages of the PIE 830 over the Altek 830

• Higher Accuracy
  Accurate to 0.006 mA, Pt 100 Ohm RTD to 0.2°C/0.4°F, Type K to 0.3°C/0.6°F, pH to 0.003 pH
• Loop Diagnostics - Unique to PIE
  Only multifunction calibrator that can power up a loop and tell you that there is moisture, corrosion or a ground fault causing current to leak to ground.
• Simulates a pH probe
  Calibrate pH tranmitters & analyzers before attaching probe to verify that each is working correctly.
• Isolated internal 24 V loop supply
  Calibrate 2-wire transmitter with electrical isolation between the input and the output for more accuate and stable readings.
• Wider range of pressure modules & scales
  Choose from 32 different modules with up to 32 engineering units for greater compatability with your processes.
• Works with more instruments
  Compatible with smart transmitters, multichannel recorders, PLCs and DCSs - GUARANTEED! More Thermocouple & RTD ranges with 0.1° resolution and better accuracy.
• Smaller & lighter
  Pocket sized and easier to carry
• LED for optical pickups
  LED flashes green in sync with frequency output. Illuminates red for overload conditions.
• Easier to hook-up
  Diagrams are shown on the display indicating where to plug in the test leads.